Bed Assembly & Care

How to Assemble an Ottoman Bed

Grey fabric ottoman bed with the mattress platform lifted on gas struts showing the storage space

Assembling an ottoman bed is manageable if you work in the correct order. The outer frame is usually straightforward; the part that needs patience is the lifting mechanism. Gas struts are pressurised, the mattress platform is heavy and small alignment errors can stop the bed from opening smoothly.

Most ottoman beds require two adults and around 90 minutes to assemble. Larger frames, side-opening designs and models with separate storage boards may take longer.

One rule matters above all: keep the manufacturer’s instructions beside you. Bolt positions, mattress limits and gas-strut orientation differ between beds. The steps below explain the usual assembly process, but your model’s manual takes precedence.

What you will need

Most of the specialist fittings should arrive with the bed. Before opening every packet, check that you have:

  • The supplied Allen key and spanner
  • A cross-head screwdriver
  • A tape measure
  • A blanket or flattened cardboard to protect the floor
  • Enough clear space to lay out the mattress platform

Avoid using a drill unless the instructions specifically permit it. Powered tools make it surprisingly easy to strip a threaded insert or overtighten a pivot bolt.

Sort the hardware against the parts list before starting. Keep left- and right-hand lift mechanisms separate, and do not begin if a bracket, bolt or strut is missing or damaged.

1. Decide where and how the bed will open

Ottoman bed panels, slatted platform, gas struts and fittings laid out on cardboard in a bedroom

Build the bed in the room where it will stay. Once assembled, an ottoman frame is awkward to move and dragging it can damage the centre legs or floor.

For an end-opening bed, leave enough room at the foot end to stand and pull the handle comfortably. Some side-opening models can be built to open from either side. If yours can, choose the opening side before fitting the lift brackets.

Check for sloping ceilings, low windows, radiators and bedside furniture. The mattress platform needs an unobstructed path when raised.

2. Assemble the outer frame

Hands bolting a grey upholstered side rail to the foot end of an ottoman bed frame

Connect the side rails to the headboard and footboard using the specified bolts, washers and brackets. At this stage, tighten the fittings only by hand. A little movement will help you align the frame correctly.

Fit the centre support rail, corner brackets and support legs where supplied. Every centre leg should meet the floor. A leg hanging a few millimetres above it will eventually place unnecessary strain on the rails and slats.

Take extra care with upholstered or wooden panels. Work on a soft surface and support long side rails instead of allowing their weight to hang from one corner joint.

3. Square the frame before tightening it

Tape measure stretched diagonally across an ottoman bed frame to check it is square

Measure diagonally from one inside corner of the bed to the opposite corner, then measure the other diagonal. The two measurements should be equal, or very close. If they are not, gently adjust the frame.

Once the bed is square, tighten the corner fittings gradually, moving between opposite corners. Do not fully tighten one corner while the others are loose.

This step prevents a common problem: a lifting platform that rubs against one side of the frame or appears crooked when closed.

Fit the storage floor panels at the stage shown in your instructions. On many designs, they are much harder to install once the mattress platform is attached.

4. Fit the lifting mechanism and mattress platform

Gas strut and hinge bracket of an ottoman lifting mechanism fixed inside a grey bed frame

Identify the left- and right-hand lift mechanisms from their labels or diagrams. Attach them to the side rails using the stated holes. Do not guess the position; using the wrong holes changes the lifting angle and can prevent the platform from closing.

Assemble the metal or slatted mattress platform separately. Fit its centre bars, slats, lifting strap and mattress retaining bar as shown in the manual.

With one person on each side, lift the completed platform onto the mechanism arms. Insert all the connecting bolts loosely before tightening any of them. Centre the platform so the gap around it is even, then tighten the fittings.

Attach the gas struts in the precise orientation and order shown by the manufacturer. Some beds arrive with them already fitted, while others require the platform to be raised and supported as they are connected. Never dismantle, puncture or try to compress a gas strut by hand.

A pivot nut may need a small amount of clearance so the joint can move. Only leave such a gap if the bed’s instructions show one; overtightening a moving joint can make the mechanism bind.

5. Fit the correct mattress before testing

Mattress resting on the closed platform of a grey ottoman bed with a pull strap at the foot

Install the mattress stoppers, handle and safety support bar before operating the bed. Then place the correct mattress on the platform.

Gas struts are selected to work within a particular mattress-weight range. Without the mattress, a new mechanism may feel extremely stiff and can resist closing. Do not sit on the raised frame or use your body weight to force it down.

Remove loose bedding, hold the supplied strap or handle with both hands and apply steady pressure. Keep your fingers away from the hinges. Raise the platform fully and engage the safety support bar if your bed has one.

Some manufacturers recommend opening and closing a new mechanism several times to bed in the strut seals. Follow the number of cycles stated in your manual.

Final safety checks

Before using the storage space, confirm that:

  • The platform opens evenly and remains securely raised
  • The safety support bar engages correctly
  • All brackets and retaining bars are firmly attached
  • Children and pets are clear of the bed while it is moving
  • Stored items cannot touch the slats or lifting mechanism

Always open the platform fully before reaching into the storage area. Never reach through the lift mechanism, and do not allow anyone to sit or lie on the mattress while it is raised.

What to check if the bed does not work properly

If the platform will not close, confirm that the mattress is fitted and falls within the required weight range. New struts can be firm, but forcing them is unsafe.

If the platform will not stay open, the mattress may be too heavy or a strut may be incorrectly fitted. Stop using the storage area until you have checked the instructions or spoken to the retailer.

When one side sits higher than the other, compare the bracket positions on both rails. Also check that the outer frame is square and that both sides of the platform use matching bolt holes.

For squeaking or movement, inspect the corner bolts, centre rail and support legs. Recheck the fixings after the first few weeks of use, as a newly assembled frame can settle slightly.

If you have not chosen a frame yet, the Fialond end-lift ottoman divan bed and the Noreldris side-lift ottoman divan bed show the two opening directions to plan around.

Conclusion

A good ottoman bed assembly depends on alignment rather than force. Square the outer frame, match the lift brackets on both sides and test the mechanism only with the correct mattress fitted. Those details determine whether the bed opens smoothly and remains safe to use.

Keep the assembly manual somewhere accessible. Mattress limits, safety supports and replacement strut ratings are model-specific, so the original instructions will remain useful long after the bed has been built.

FAQs

Can one person assemble an ottoman bed?

It is not recommended. Two adults are normally needed to position the heavy mattress platform and connect the lifting mechanism safely.

Why is my new ottoman bed difficult to close?

The gas struts may be stiff because they are new, or the mattress may be missing or too light. Fit the specified mattress and follow the first-use instructions without forcing the frame.

Which way should the gas struts face?

Follow the diagram supplied with your bed. The correct orientation varies between mechanisms, so do not rely on a general rule or another bed’s instructions.

How long does an ottoman bed take to assemble?

Allow roughly 90 minutes for a typical frame. Large, side-opening or more complicated models may take two hours or longer.

Can I use any mattress on an ottoman bed?

The mattress must be the correct size and within the mechanism’s stated weight range. A mattress that is too light or heavy can prevent the platform from operating safely.

Leave a Reply

Your email address will not be published. Required fields are marked *